Iron Edison

Nickel Iron (NiFe) Lithium Iron (LiFePO4)

Free System Design! Call 720-432-6433

Charge Controllers / Morningstar TriStar 600v MPPT Charge Controller

Morningstar TriStar 600v MPPT Charge Controller

Free system design.

No obligations.

Send any questions.

    Configure this product

    Item added to order

    Morningstar TriStar MPPT 600 VDC Charge Controllers
     

    The TS-MPPT-600V uses Morningstar’s TrakStar™ MPPT technology coupled with the widest PV input operating-voltage range available in a PV controller. The high-speed sweeping algorithm of the TrakStar™ MPPT technology enables this charge controller to harvest the maximum energy from a solar array under all ambient conditions.

    The TS-MPPT-600V charge controllers are rated for 60 A output to charge 48 VDC battery systems, and can be programmed to charge 24 VDC or 60 VDC battery systems. Their wide input operating voltage range of 100-525 VDC, 600 VDC maximum open-circuit voltage limit, and buck-boost design, allow flexible string sizing that also mitigates PV shading. A four-stage charging algorithm helps to optimize battery health.

    The TS-MPPT-600V controller is Ethernet enabled for remote communications, data logging, adjustability, and metering. Communication ports/interfaces include Ethernet, EIA-485, RS-232 and MeterBus.

    Built-in lightning protection protects the circuitry from nearby lightning-induced voltage/current spikes. The large heat sink provides convective cooling without fans, so there are no moving parts. Continuous full power operation up to 45 °C ambient temperatures. The printed circuit boards are conformal coated for protection against moisture and dust. Self-diagnostics and electronic error protections help reduce the risk of installation missteps.

    The TriStar MPPT 600 V charge controller is available with or without a pre-wired DC Disconnect Box. The pre-wired DC Disconnect Box version, the TS-MPPT-60-600V-48-DB, can be used with positively grounded or negatively-grounded PV systems and has both array and battery disconnects.

    TriStar MPPT 600 VDC Charge Controllers w/ Array Transfer Switch
     
    The TriStar charge controller is now available as the TS-MPPT-60-600V-48-DB-TR with an array transfer switch. This 30 A, 600 VDC double-pole, double-throw switch will enable the Tristar to be installed between the PV array and a grid-tie inverter so that during a utility outage, the array can be switched to charge a battery backup system. This arrangement does not require any compatibility between the grid-tie inverter and battery inverter, and is extremely reliable as a retrofit backup-power solution to a grid-tie PV system. The backup system can be made to fit only the backup requirements, not the equipment requirements. A larger PV array can be fed into one charge control for higher output during cloudy periods, and will simply limit the charge at 60 A (or lower setting) when there is more power available from the array. 

    The TS-MPPT-60-600V-48-DB-TR-GFPD is the same control with transfer switch, and includes Morningstar’s advanced ground-fault-protection device with the control. 
     
    A battery-temperature sensor (RTS) is included. Wire terminals accept #14 to #2 AWG wire. All units are NEMA1 rated for indoor installation (IP20). Listed to UL 1741 and Canadian CSA C22.2 No. 107.1.01. FCC Class B Part 15 compliant.
     
    Ambient operating temperature range: -40 ºF to +113 ºF (-40 ºC to +45 ºC).
     
    These charge controllers are covered by a 5-year warranty.

    starting from $1,575.98

    720-432-6433

    Give us a call
    We are happy to help!

    or email Info@IronEdison.com

     
    A brighter future, off the grid.

    A brighter future. Off the grid. Iron Edison battery systems can be used for 12, 24 and 48 volt applications. We can also help you optimize battery capacity to take better advantage of the solar, wind and other hardware you may already have in place.

    forever stamp
      ×

      Learn More